BIO RAD 400-0174 Provozní pokyny Strana 334
- Strana / 485
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Maintenance – Mowing Units
334
Pos: 28.24.13.2 /Ü berschriften/Ü berschriften 3/K-O /Ölwechsel @ 0\mod_119 7021941955_ 78.doc @ 161 39
14.14.3 Oil change
Pos: 28.24.13.2 / BA/Sicherheit/G efahrenhin weise/Mähwerke/ Schnell rotieren de Messerteller/M essertrommeln _1 @ 0\mo d_119701769 6736_78.doc @ 1 6001
Danger!
Rapidly rotating cutting discs/blade drums.
Effect: Danger to life or serious injuries.
• Switch off the engine and remove the ignition key.
• The cutting discs/blade drums continue to run!
• Do not leave the driver’s cab until the cutting discs/blade drums have
come to a complete stop.
Pos: 28.24.13.2 / BA/Wartung/M ähwerke/Ölwec hsel seitliche M ähwerke Big M 4 00 @ 0\mo d_119702850 6408_78.doc @ 16 241
Fig. 294:
• Fold up the right/left lateral mowing units (1).
• Collect the used oil in a suitable drip pan.
• Remove the lower cover (2) on the cutter bar.
• Reinstall cover (2) with new seal.
• Add oil at the lower inspection screws (3).
• Check oil level (see chapter "Checking the Oil Level").
Note
• Always check the oil level after repair work on the cutter bar.
Pos: 28.24.13.2 / BA/Wartung/Öl kontrolle_Wechs el/Ölqualität /Öl menge: siehe K apitel @ 0\ mod_119700 7859486_78.doc @ 15531
Oil quality / oil quantity: see Chapter "Filling Quantities and Lubricant Designations for
Gearboxes"
Pos: 28.24.13.3 / BA/Wartung/Öl kontrolle_Wechs el/Altöl ordnungsge mäß entsorg en @ 0\mo d_119700811 7002_78.doc @ 15550
Note
The used oil must be disposed of correctly
Pos: 28.25 /BA/-----Seitenu mbruch------ @ 0\mod_119617 5311226_0. doc @ 4165
BMII-370
2
1
BMII-371
3
- Mower-Conditioner 1
- 1 Table of Contents 2
- Table of Contents 10
- Foreword 13
- 2 Foreword 13
- Introduction 14
- 3 Introduction 14
- 4 Safety 19
- Safety 20
- Safety 21
- Grund: gelb 23
- Schrift: schwarz 23
- Kreuz: rot 23
- Close valve when 27
- 1.2 bar 29
- BM 400 0181 30
- 12V / 24 V 31
- BM 400 0123 33
- BM 400 0182 34
- BM 400 0183 34
- BM 400 0001 35
- Cabin 36
- BX100280 39
- BM 400 0171 41
- BM 400 0016 43
- BX100210 45
- BX100213 45
- BX100212 46
- BM 400 0017 47
- BM 400 0187 49
- BM 400 0188 51
- BM 400 0192 55
- BM 400 0193 55
- BM 400 0145 57
- BM 400 0194 59
- BM 400 0146 60
- BMII-197 61
- BMII-196 62
- BM 400 0005 65
- BX 400 0006 66
- BM 400 0009 68
- BM 400 0012 72
- BM 400 0013 73
- BM 400 0014 74
- BM 400 0015 75
- BMII-200 89
- Cabin 91
- BM 400 0099 92
- BM 400 0100 93
- I 115:36 95
- changes to red 96
- BM 400 0116 97
- BM 400 0114 98
- BM 400 0105 98
- BM 400 0106 100
- BM 400 0103 100
- BM 400 0107 103
- BM 400 0108 104
- BM 400 0117 104
- BM4000109 105
- BM 400 0110 106
- BM 400 0104 108
- BM 400 0111 109
- BM 400 0032 110
- BM 400 0050 112
- BM 400 0051 113
- BM 400 0019 114
- BM 400 0021 115
- BM 400 0020 115
- BM 400 0033 116
- BM 400 0034 116
- BM 400 0112 119
- BM 400 0037 120
- = Metric (SI) units 121
- BM4000224 122
- BM4000225 123
- BM 400 0022 124
- BM 400 0023 124
- BM 400 0025 125
- BM 400 0024 125
- BM 400 0026 126
- BX500045 127
- BX500044 127
- BM 400 0027 128
- BX500046 128
- BM 400 0028 129
- BX500075 130
- = left mowing unit 133
- = front mowing unit 133
- = accept right mowing 133
- BM 400 0085 134
- BM 400 0038 137
- BM 400 0120 139
- BM 400 0121 140
- BM 400 0040 141
- BM 400 0039 141
- Actuator turned off 143
- Actuator turned on 143
- BM 400 0043 144
- BM 400 0042 144
- BM 400 0046 149
- BM 400 0052 149
- BM 400 0048 154
- BM 400 0054 157
- BM 400 0053 157
- BM 400 0058 162
- BM 400 0057 162
- BM 400 0062 168
- BM 400 0063 169
- BM 400 0064 171
- BM 400 0065 173
- BM 400 0067 177
- BM 400 0073 178
- BM 400 0068 179
- BM 400 0072 179
- = Cruise control inactive 181
- = Parking brake is applied 181
- BM 400 0069 185
- BM 400 0070 187
- BM 400 0074 188
- BM 400 0076 189
- BM 400 0075 189
- = Engine oil temperature 190
- BX500161 191
- BM 400 0079 191
- BX500190 192
- BM 400 0080 192
- Key not activated 193
- Key activated 193
- Broken cable 193
- Short circuit 193
- BM 400 0082 194
- BM 400 0081 194
- Key not activated 196
- Key activated 196
- = Current error 197
- = Fault storage 197
- key under the softkey 198
- key under the softkey 199
- A key under the softkey 200
- BX500126 201
- BM 400 0091 201
- BX500128 202
- BX500127 202
- BM 400 0092 203
- BM 400 0094 204
- BM 400 0095 204
- BM 400 0096 204
- BX500135 205
- BX500136 205
- -1.9 -1.8 206
- BM 400 0097 206
- BX500137 206
- BM 400 0113 207
- BM 400 122 208
- Commissioning 209
- 7 Commissioning 209
- BM 400 0148 213
- Start-up 214
- 8 Start-up 214
- Driving and Transport 216
- 9 Driving and Transport 216
- BM 400 0196 217
- BM 400 0007 219
- BMII-285 219
- BM 400 0010 220
- BMII-187 222
- BM 400 149 224
- BX100801 224
- BX100802 226
- BX500037 228
- BX500038 229
- BM 400 150 230
- BM 400 151 230
- BM 400 0008 232
- BMII-186 233
- Operation – Mowing Units 235
- 10 Operation – Mowing Units 235
- BMII-252 248
- BM 400 0147 250
- BX500036 255
- BX500035 255
- BM 400 0011 256
- Adjusting the mowing units 257
- BM 400 0175 258
- BM 400 0176 259
- BMII-189 263
- SFM05230 264
- BMII-372 268
- BMII-287 270
- BMS01030 276
- BMS01100 277
- BMS01071 278
- BMS01210 279
- BMS01270 280
- BMS01340 281
- BM301080 282
- BM300190 282
- BMII-276 284
- BMII-275 284
- BM 400 0160 285
- BM 400 0142 287
- Both augers on 288
- Right auger on 288
- Left auger on 288
- BMII-312 290
- BM 400 0161 291
- BMII-307 292
- BMII-308 293
- BM 400 0162 294
- BMII-311 295
- BMII-313 296
- BMII-314 298
- BMII-315 299
- BMII-320 300
- BMII-316 301
- BM 400 0163 302
- BMII-318 303
- BMII-319 305
- Maintenance - Engine 307
- 13 Maintenance - Engine 307
- BMII-180 310
- Maintenance – Mowing Units 318
- On request 322
- BMII-363 331
- EC-239-0min. 14 mm 337
- Maintenance – Basic Machine 349
- BMII-202 353
- BM 400 0165 358
- BMII-203 360
- BM 400 0166 362
- BM 400 0204 364
- BMII-215 367
- BMII-134 368
- BM 400 0205 370
- SFM1-510 372
- BM 400 0167 374
- BMII-365 378
- BMII-328 379
- BM 400 0212 380
- BM200551 382
- BMII-231 383
- BM 400 0144 388
- BM 400 0207 389
- BM 400 0208 390
- BX500088 391
- BiG M 400 Cab Circuit Board 393
- BX110007 395
- BX110008 395
- BX110009 396
- BX110010 396
- BX101960 399
- keys to select the 400
- Placing in Storage 402
- 19 Placing in Storage 402
- Error Messages 406
- Display fault 9 452
- Display fault 10 452
Související produkty a manuály pro Čtečky čárových kódů BIO RAD 400-0174
(25 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.082 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce